Carved box and 2 chairs for sale

A couple of things for sale, brought down from the loft. If you’d like any of these, leave a comment and we’ll take it from there. Paypal or check is fine, I add the fees to the paypal charges. If someone beats you to it, I can always make these sort of things on order.

I’ll start with the box. I made quite a few boxes last year, particularly in the fall. This box is #12 of 11, or something like that. I made the body of it then, but didn’t finish it until a week ago or so. It’s quartersawn red oak, with a white pine bottom. The carvings are based on boxes made in Dedham, Massachusetts in the 2nd half of the 17th century.

My schedule is pretty full with the large cupboard I’m making and some stools and chairs. I know I’ll make more boxes this year but don’t know when. And there won’t be as many as last year.

H: 10 1/2″ W: 26 1/2″ D: 14 3/4″
$1,200 includes shipping in US

carved box red oak white pine
open showing till

The till parts were scrounged from what was in the shop at the time, a walnut lid and red cedar bottom & side.

detail of front corner

The boxes I make depart from “typical” period boxes in that the sides are carved in addition to the front. This is seen on some period boxes, but most are just carved on the front. I use wooden pegs and glue to secure the rabbets – same story – most period boxes are nailed there, some are pegged. And I use a wooden hinge, again, you see that sometimes, but more often iron hinges.

——————

Ladderback chair
Hickory rungs and posts, red oak slats, hickory bark seat.

H: 33 1/2″ W: (across front posts) 17 1/2″ D: (overall) 18″ Seat height 17 3/4″

ladderback chair

There’s a story to this chair. I fumbled around a bit when I was re-learning how to make these chairs. This one I got the orientation of a rear post a bit off, resulting in what Drew Langsner calls a “windswept” back to the chair. Just a bit asymmetrical. It’s perfectly sound and sits fine. It’s just not a top-flight chair. But neither is it a “second.” I guess it’s a “second & 1/2.” When I assembled it, I saw the problem and stuck it in the loft and made another. Recently I got it out & decided it’s not that bad – so I put a hickory bark seat on it and took $200 off the price.

$1,000 including shipping in US.

You can see the post on our right is kicked out too far. Not fatal.

front view

Here’s the hickory bark seat.

hickory bark seat

———————–

Kid’s size ladderback chair

H: 26″ W: (across front) 14 1/4″ D: (overall) 14″ Seat height 14″
$800 including shipping in US.

Kid’s ladderback

A colored chair? From me? Yup, it’s to hide another mishap. Bored a hole in the wrong spot, plugged it & carried on. But it was right in a front post. So I practiced coloring this one. Even with the plugged joint, the chair is perfectly sound. Here’s the plugged mortise, at the rung that’s running down to the right in this photo.

plugged mortise

—————-

I still have two brettstuhls here, Alpine chairs, board-chairs – whatever you might call them. It’s funny to think about me making Alpine chairs down here at sea level. They might seem like quite a departure from my normal work, but with carved decoration, mortise & tenon joinery and a long tradition, they are right up my alley. If anyone is interested in one, send me an email at PeterFollansbee7@gmail.com 

brettstuhl walnut & ash

Next chair

(as I’ve been working on blog posts lately, things have been a bit weird. When I preview the post, to see the photos larger, I have to click them twice – first they go tiny, then the 2nd click enlarges them. That’s all I can tell you – otherwise, you’re on your own.)

I’ve made lots of kinds of chairs over the years, but the chair I started today is only my third attempt at a “brettstuhl”. Six or more years ago, I did one in walnut with hickory legs. As soon as I got this one done, I saw the flaw – I tapered the legs the wrong way!

walnut & hickory, 2014

It’s funny looking at that photo now – the chair is sitting right where my shop is now. So today I started in at the beginning, working some beautiful ash – and tapering those legs DOWN to the feet. The instructions I’m using on making this chair are from Drew Langsner’s Fine Woodworking article “Two Board Chairs” in the July/August 1981 issue. Below you see one leg done, the other riven oversized. You can make these at the shaving horse, but I did them today at the bench. (I sat at my desk all day yesterday & didn’t feel like sitting.)

First step is to plane two faces, then bring the whole thing to about 1 3/8″ square. This is very fresh wood, just split open a week ago. I want it to finish about 1 1/4″ at the thick end.

Then mark out the tapered foot, and plane down to that. See the end grain of this stick, I’ve drawn a 1″ square as my target to plane down to.

The fresh green wood planes so easily. Dead-straight makes it easy too. I make the octagonal cross-section after tapering. The piece is sitting up in a v-block behind me, and that brings it “corner up.” First shavings here are whisper thin (narrow, really, but who says “whisper-narrow?”)

I start near the foot and take a few strokes, then begin backing up as I plane forward. After a couple of strokes, the shavings get wider and wider.

There – I’ve got that mistake from six years ago remedied. Now on to the back board. I made a half-template out of 1/2″ thick pine and just traced around it. The board is quartersawn butternut, 7/8″ thick.

I’m no master with a bowsaw/turning saw. I get close, then fine-tune the result. I make stop cuts here & there, and apply beeswax to the tiny little teeth. And I keep telling myself, “easy does it.” This saw I made years ago with the hardware from Tools for Working Wood. https://toolsforworkingwood.com/store/item/GT-BOWS.XX?searchterm=bowsaw

Here, I followed some of the shape with a spokeshave.

Then I went over some of the detailed edges with a couple of carving gouges.

Here’s as far as I got – the holes I bored are to put the saw in to cut out the hand-hold. It was getting pretty low light in the shop, so I decided that was a good time to quit. Tomorrow’s another day.

I’m interrupting my interruptions

Took some time away from the carved box w drawer, to work with some funny wood. Yes. I’ve returned once again to using Juglans…

First up, juglans nigra….yes, nigra. Remember my struggles with black walnut? https://pfollansbee.wordpress.com/?s=walnut+high+chair   Well, of course the first go ’round I can blame on poor quality stock; kiln-dried, random-sawn lousy trees.

the 2nd time around, I got very clear, straight-grained, air-dried stock, and it’s two off-cuts from that batch that I’m working now.

walnut carving

But first, some green wood – a bowl from Juglans cinerea; butternut. That’s what I’m interrupting my interruption for…this could be fun…if that jackhammer next door would quit.

bowl butternut