The Essex County cupboard project: recessed front stiles

Many irons in the fire. Between brettstuhls and other things, we spit out the next video for the cupboard project. This one’s about the short, wide recessed front stiles in the lower case. This photo below shows a partially-assembled end section to the lower case. On the bench is the rear stile, the two wide/tall rails we’ve seen before. Between them is the muntin in the middle, and near the top of the photo the piece I’m calling the “recessed front stile” (for lack of a better term, and that’s what it is.)

These stiles are, in New England furniture, unique to this shop’s production as far as I can remember. I started them by laying out and chopping the mortises for the drawer rails. These stiles frame a section that houses two drawers – the lower one about 7″ deep, the upper one about 4″. Between and above & below the drawers are narrow/short rails – 1 1/4″-1 1/2″. Once the mortises were cut, I laid out and cut the tenons that fit this stile between the rails.

The photo below is a bit dark, but you can see perhaps the layout of the near tenon. The odd thing about it to me is that it’s in the tangential plane. Most tenons are in the radial plane in stock like this – so I drew all over it with pencil. Didn’t want any more mishaps. You can see the pin holes bored in the stile’s face where I have the mortises chopped.

Now for the rear shoulder. Switched to a bigger saw and cut those shoulders down to the line. This opens up the top bottom mortises, turning them into what I think of as bridle joints. But these will never show regardless.

Then it’s just a matter of splitting off the waste & paring it, like I do for most of my tenons.

These stiles are chunky, 1 7/8″ x 4 7/8″ – so inside there’s still some moisture. I got some resulting checks on the newly-exposed end grain once I formed the tenons of the first one. (I cut one for still photos, one for videos and there might have been a day in between). Nothing fatal, but on the 2nd one I glued those ends after cutting it. Just to reduce the chance of a split carrying into the edge of the stile.

Below is the whole thing in a short 11-minute video. A new record for me, usually I go on & on. It shows how they all fit together, so might help make sense of this slightly-weird construction. I hope by the end of the month to be able to test-fit the bulk of the framing, both upper & lower cases.

(pt 14 Essex County cupboard project 2021)

6 thoughts on “The Essex County cupboard project: recessed front stiles

  1. Seems like an enormous amount of weight and [otential tprque could be exerted on those front recessed stiles, particularly when you factor in the weight of the drawers. Can’t remember if the oak shelves are radial in cross-section ornot. Nor am I remembering how the soffits are framed.

    • Trent – there’s lots I forget and our notes don’t tell me. I’m making a list of things I hope to go check. I’d hate to improvise. How these drawer runners attach at the rear for instance. There’s no rear stiles behind these inset one. That little shelf above the lowest drawer, in front of these stiles, is riven/radial. The soffit here I think I’ll do just like the one at the top of the upper case. Nailed down to the inner framing and beveled into a groove in the overhanging rails. But now we’re so ahead of things no one can follow. It’s too weird until you see it.

  2. I don’t think I could have ever conceived of a frame piece like that. Seems like a really unusual construction method.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s